{"title":"Benches \u0026 Stations","description":"\u003cp\u003eThe work surfaces that earn their floor space. A modular drawer workbench in 48 and 60 in, a flip-top station that parks two benchtop tools in one footprint, and the crosscut + router sled duo that makes the table saw honest. Drawer math, pivot geometry and calibration formulas — computed in the plans, not left to luck.\u003c\/p\u003e","products":[{"product_id":"flip-top-tool-station-woodworking-plan","title":"Flip-Top Tool Station — Woodworking Plan","description":"\u003cp\u003eTwo benchtop tools, one footprint. The top flips, so the planer and the sander trade places in seconds, and the idle tool waits underneath. We printed the pivot geometry in the plan — rotation sweep, clearances and all — because a flip top that clips its own cabinet is a drawing error, and you'd rather find that on paper than mid-build.\u003c\/p\u003e\n\u003ch2\u003eThe numbers\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eFinished size: 30 × 24 × 33 in (W × D × H) — carcase height; specified 3 in casters add about 4 in of standing height\u003c\/li\u003e\n\u003cli\u003ePlan length: 16 pages (US Letter), imperial + metric throughout\u003c\/li\u003e\n\u003cli\u003eFlip panel: 26¾ × 24 in on a steel rod through two cheek blocks; holds tools up to 12 in tall on a 26 × 22 in centred footprint\u003c\/li\u003e\n\u003cli\u003eInterior: one fixed shelf low at 6 in with tall open space above — the back panel stops at 18 in so the flipping panel's corner sweep (≈12 in radius) can never strike it; the sweep math is printed in the plan\u003c\/li\u003e\n\u003cli\u003eSheet goods: 1 × ¾ in plywood sheet + 1 × ¼ in plywood sheet\u003c\/li\u003e\n\u003cli\u003eEstimated material cost: $170, worked out from the cut list\u003c\/li\u003e\n\u003cli\u003eDifficulty: Intermediate · Build time: 1 day\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat's included\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e16-page plan (Letter, print or tablet) — imperial \u0026amp; metric throughout\u003c\/li\u003e\n\u003cli\u003eFront, side \u0026amp; top elevations + a full exploded view, all dimensioned in inches and millimetres\u003c\/li\u003e\n\u003cli\u003ePivot geometry checked in the model: sweep clearances printed on the steps\u003c\/li\u003e\n\u003cli\u003eRod and locking-pin drilling positions given from one datum line\u003c\/li\u003e\n\u003cli\u003eDXF + SVG cutting files, grouped by real material thickness\u003c\/li\u003e\n\u003cli\u003eExact hardware list — rod, pins and caster specs included, no guesswork\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eTools\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eCircular saw with a straightedge guide (or table saw \/ track saw)\u003c\/li\u003e\n\u003cli\u003eDrill\/driver, pocket-hole jig, and a 3\/8 in bit long enough for the rod holes\u003c\/li\u003e\n\u003cli\u003eClamps (2 × 24 in), combination square, tape, level\u003c\/li\u003e\n\u003cli\u003eOrbital sander — no CNC required. CNC files are included if you have one.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eIs this a physical product?\u003c\/strong\u003e No — it's an instant digital download: the plan PDF plus DXF and SVG cutting files. Nothing ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat size tools fit?\u003c\/strong\u003e Tools up to 12 in tall on a 26 × 22 in centred footprint. That limit comes from the panel's rotation sweep, and the plan shows the math.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy is the back panel short?\u003c\/strong\u003e On purpose. A full-height back would be struck by the flipping panel's corner, so the back stops at 18 in and the fixed shelf sits low. Both are sweep clearances, explained in the plan.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat do the plans look like?\u003c\/strong\u003e We put real pages from the plan on this page — the cover, the cut list and the sheet layout — so you can see what you're buying before you pay.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need a CNC?\u003c\/strong\u003e No — circular saw and drill work fine. The CNC files are included free, grouped by actual thickness.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat if the files don't open, or something in the plan is wrong?\u003c\/strong\u003e Email us at a1809991767@gmail.com and we'll send you a new copy free. If a dimension in the plan is wrong, that's on us — tell us and we'll fix it and send you the corrected files. And if your download link ever expires, email us and we'll send you a new one.\u003c\/p\u003e","brand":"Northpine","offers":[{"title":"Default Title","offer_id":48336458481836,"sku":"NP-FLIP-TOP","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0786\/1207\/0572\/files\/01-hero_7993e94a-d457-4d67-a311-68962fed48f2.png?v=1794276080"},{"product_id":"modular-drawer-workbench-woodworking-plan-60-in-48-in","title":"Modular Drawer Workbench — Woodworking Plan (60 in \u0026 48 in)","description":"\u003cp\u003eA small-garage bench that works like a big one: a laminated double-thickness top, three real drawers where your right hand expects them, and an open bay with a shelf where the shop vac lives. The drawer math is done for both widths — the drawer boxes are sized from the measured opening, and the formula is printed in the plan so the drawers fit the bench you actually built.\u003c\/p\u003e\n\u003ch2\u003eThe numbers\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eFinished sizes: 60 × 24 × 36 in · 48 × 24 × 36 in (W × D × H)\u003c\/li\u003e\n\u003cli\u003ePlan length: 19 pages (US Letter), imperial + metric throughout\u003c\/li\u003e\n\u003cli\u003eTop: two laminated layers of ¾ in plywood\u003c\/li\u003e\n\u003cli\u003eStorage: 3-drawer bank on the right half (¾ in overlay fronts at 7-9\/16 in pitch fill the 22¾ in opening exactly; ½ in drawer bottoms) + open shelf on the left half at 12 in\u003c\/li\u003e\n\u003cli\u003eFrame: 2×4 leg and end frames\u003c\/li\u003e\n\u003cli\u003eSheet goods: 2 × ¾ in plywood sheets + 1 × ½ in plywood sheet (either width)\u003c\/li\u003e\n\u003cli\u003eEstimated material cost: $266.50 — the same for both widths; the 48 in rails nest onto the same board count, and the plan's board layouts show it\u003c\/li\u003e\n\u003cli\u003eDifficulty: Intermediate · Build time: 1 weekend\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat's included\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e19-page plan (Letter, print or tablet) — imperial \u0026amp; metric throughout\u003c\/li\u003e\n\u003cli\u003eFront, side \u0026amp; top elevations + a full exploded view, all dimensioned in inches and millimetres\u003c\/li\u003e\n\u003cli\u003eTwo widths in one plan: 60 in and 48 in, drawer math done for both\u003c\/li\u003e\n\u003cli\u003eDrawer boxes sized from the measured opening — the formula is printed in step 5\u003c\/li\u003e\n\u003cli\u003eDXF + SVG cutting files, grouped by real material thickness\u003c\/li\u003e\n\u003cli\u003eExact hardware list — slide and screw specs included, no guesswork\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eTools\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eCircular saw with a straightedge guide (or table saw \/ track saw)\u003c\/li\u003e\n\u003cli\u003eDrill\/driver and a pocket-hole jig\u003c\/li\u003e\n\u003cli\u003eClamps — the top lamination wants six if you have them\u003c\/li\u003e\n\u003cli\u003eCombination square, tape, level; a vice to mount when it is done\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eIs this a physical product?\u003c\/strong\u003e No — it's an instant digital download: the plan PDF plus DXF and SVG cutting files. Nothing ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy does the 48 in bench cost the same to build as the 60 in?\u003c\/strong\u003e Because the shorter rails nest onto the same number of boards. It's in the plan's board layouts, not a typo.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAre the drawers on slides?\u003c\/strong\u003e Yes — the hardware list specs the slides, and the drawer boxes are sized from your measured opening using the printed formula.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat do the plans look like?\u003c\/strong\u003e We put real pages from the plan on this page — the cover, the cut list and the sheet layout — so you can see what you're buying before you pay.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need a CNC?\u003c\/strong\u003e No — it's a circular-saw build. CNC files are included free, grouped by actual thickness.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat if the files don't open, or something in the plan is wrong?\u003c\/strong\u003e Email us at a1809991767@gmail.com and we'll send you a new copy free. If a dimension in the plan is wrong, that's on us — tell us and we'll fix it and send you the corrected files. And if your download link ever expires, email us and we'll send you a new one.\u003c\/p\u003e","brand":"Northpine","offers":[{"title":"Default Title","offer_id":48336470081708,"sku":"NP-WORKBENCH","price":10.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0786\/1207\/0572\/files\/01-hero_cf702365-ac1f-41b3-9f7d-30a6de79af40.png?v=1794276090"},{"product_id":"crosscut-router-sled-duo-woodworking-plan","title":"Crosscut + Router Sled Duo — Woodworking Plan","description":"\u003cp\u003eThe two jigs that make a table saw and a router behave — in one plan, for the price of a coffee. A crosscut sled that calibrates dead-square with the five-cut method, error formula worked for you, and a router sled for flattening stock too wide for your planer. The router sled is drawn stored on the crosscut sled, which is where it will live in your shop too.\u003c\/p\u003e\n\u003ch2\u003eThe numbers\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eCrosscut sled: 24 × 18 in base in ½ in plywood, tall rear fence (the working fence), low front safety fence, two hardwood miter bars ripped from a 1×4\u003c\/li\u003e\n\u003cli\u003eRouter sled: 20 × 14 in base with two rails the router bridges across\u003c\/li\u003e\n\u003cli\u003ePlan length: 16 pages (US Letter), imperial + metric throughout\u003c\/li\u003e\n\u003cli\u003eCalibration: the five-cut method, with the error formula worked in the plan — square is measured, not hoped for\u003c\/li\u003e\n\u003cli\u003eSheet goods: 1 × ½ in plywood sheet + 1 × ¾ in plywood sheet, plus a 1×4 for the miter bars\u003c\/li\u003e\n\u003cli\u003eEstimated material cost: $145 for both sleds, including hardware, worked out from the cut list\u003c\/li\u003e\n\u003cli\u003eDifficulty: Beginner · Build time: 1 day\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat's included\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e16-page plan (Letter, print or tablet) — imperial \u0026amp; metric throughout\u003c\/li\u003e\n\u003cli\u003eFront, side \u0026amp; top elevations + a full exploded view, all dimensioned in inches and millimetres\u003c\/li\u003e\n\u003cli\u003eTwo complete sleds: crosscut (24 x 18) and router (20 x 14)\u003c\/li\u003e\n\u003cli\u003eThe five-cut calibration method, with the error formula worked for you\u003c\/li\u003e\n\u003cli\u003eDXF + SVG cutting files, grouped by real material thickness\u003c\/li\u003e\n\u003cli\u003eExact hardware list — screw specs included, no guesswork\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eTools\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eTable saw (the sleds' home) and a drill\/driver\u003c\/li\u003e\n\u003cli\u003eCalipers — the five-cut method is only as honest as its measurement\u003c\/li\u003e\n\u003cli\u003eCombination square, clamps, a straightedge\u003c\/li\u003e\n\u003cli\u003eA router for the second sled; any flat offcut becomes its bridge\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eIs this a physical product?\u003c\/strong\u003e No — it's an instant digital download: the plan PDF plus DXF and SVG cutting files. Nothing ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill the miter bars fit my saw?\u003c\/strong\u003e The bars are ripped from a 1×4 and then planed or sanded to a sliding fit in YOUR saw's slots — the plan says to measure your slots first, because slot widths vary between saws.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow square is the crosscut sled, really?\u003c\/strong\u003e As square as your five-cut measurement says it is. The plan prints the method and the error formula, so you adjust the fence by a computed amount, not by tapping and hoping.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat do the plans look like?\u003c\/strong\u003e We put real pages from the plan on this page — the cover, the cut list and the sheet layout — so you can see what you're buying before you pay.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need a CNC?\u003c\/strong\u003e No. Both sleds are table-saw-and-drill builds; the CNC files are a free extra.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat if the files don't open, or something in the plan is wrong?\u003c\/strong\u003e Email us at a1809991767@gmail.com and we'll send you a new copy free. If a dimension in the plan is wrong, that's on us — tell us and we'll fix it and send you the corrected files. And if your download link ever expires, email us and we'll send you a new one.\u003c\/p\u003e","brand":"Northpine","offers":[{"title":"Default Title","offer_id":48336480927916,"sku":"NP-SLED-PAIR","price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0786\/1207\/0572\/files\/01-hero_de147fb6-5973-499a-b1d7-53dc8809b975.png?v=1794276098"}],"url":"https:\/\/northpineplans.com\/collections\/benches-stations.oembed","provider":"Northpine","version":"1.0","type":"link"}